Content on this page requires a newer version of Adobe Flash Player.

Get Adobe Flash player

Our Steel Products
Epoxy Coated Rebar : ASTM- A775M Grade – 60
Epoxy Coated Rebar Specification
Sizes 10mm to 40 mm
Length Up to 12 Meters
Standard ASTM- A775M Grade – 60 & BS Standard too
Delivery Capacity 5,000 Tons per month
 
Black Rebar : 8-32mm ASTM- A615, Grade - 60
Deform Rebar Specification
Size 10mm to 40 mm
Length Up to 12 Meters
Standards ASTM- A615, Grade – 60
Delivering Capacity 7,000 Tons per month
 
Black & Epoxy Cut and Bend Rebar: A 315, A-934M, BS4466 & BS 8666
Bend Rebar Specification
Cut & Bend Rebar's 8 mm to 32mm
Stirrup 5 mm to 16mm
Spiral Rings 8 mm to 32mm
Delivering Capacity 7,000 Tons per month
  Standards A 315, A-934M, BS4466 & BS 8666
 
Structural steel
Structural Steel
Section Standard Sectional Dimensions (mm) Mass Kg/m
  H B S T R  
IPE 80 80 46 3.8 5.2 5 6
IPEA 80 78 46 3.3 4.2 5 5
IPEAA 80 78 46 3.2 4.2 5 4.95
IPE 100 100 55 4.1 5.7 7 8.1
IPEA 100 98 55 3.6 4.7 7 8.1
IPEAA 100 97.6 55 3.6 4.5 7 6.72
IPE 120 120 64 4.8 6.3 7 10.4
IPEA 120 117.6 64 3.8 5.1 7 8.7
IPEAA 120 117 64 3.8 4.8 7 8.36
IPE 140 140 73 4.7 6.9 7 12.9
IPEA 140 137.4 73 3.8 5.6 7 10.5
IPEAA 140 136.6 73 3.8 5.2 7 10.05
IPE 160 160 82 5 7.4 9 15.8
IPEA 160 157 82 4 5.9 9 12.7
IPEAA 160 156.4 82 4 5.6 9 12.31
IPEA 180 180 91 5.3 8 9 18.8
IPEAA 180 177 91 4.3 6.5 9 15.4
IPEAAA 180 176.4 91 4.3 6.2 9 14.94
IPE 200 200 100 5.6 8.5 12 22.4
IPEA 200 197 100 4.5 7 12 18.4
IPEAA 200 196.4 100 4.5 6.7 12 17.95
 
Round Bar
Round Bar
Section Diameter Sectional Area Mass
  MM CM2 kg/m
R30 30 7.07 5.55
R32 32 8.04 6.31
R35 35 9.62 7.55
R38 38 11.34 8.9
R40 40 12.57 9.86
R42 42 13.85 10.9
R45 45 15.9 12.5
R50 50 19.63 15.4
R52 52 21.24 16.7
R55 55 23.76 18.7
R60 60 28.27 22.2
R65 65 33.18 26
R70 70 38.48 30.2
R75 75 44.18 34.7
R80 80 50.27 39.5
R90 90 63.62 49.9
 
Wire Mesh : 4mm – 10 mm ASTM 497,BS 4483 and SASO
wire mesh Diameter of wire 4mmto 12 mm
Sheet Length 2.0M - 6.0M
Sheet width 1.0 M - 2.75M
Spacing 100mm, 150mm, 200 mm
Standards SASO 275 ,B.S. 4483, DIN 488, ASTM A-496
 
CUT & BEND : ASTM - A775M GRADE - 60 & ASTM - A615 GRADE - 60
wire mesh Cut & Bend Rebar's 8 mm to 32mm
Stirrup 5 mm to 16mm
Spiral Rings 8 mm to 32mm
Production Capacity 15,000 MT/ Month (Dammam/Jeddah)
Standards A 315, A-934M, BS4466 & BS 8666
 
Wire Rods
wire rods Size (mm)
5.5 & 6.0 (Wire drawing)
7.0 - 14.0 (Wire drawing)
5.5 and 6.0 (Mesh)
7.00 - 14.00 (Mesh)
 
PC Strand Wire
pc strand wire  
 
Standard Diameter (mm) Area of strand (mm2) Weight of strand (kg/km) Min.Breaking Load (kn) Min. Loadat 1% Extension (kn) Min. Elo(&) Max. Relaxation at 1000 hrs.70%
Grade 1860(270) 9.53 54.8 432 102.3 92.1 3.5 2.5
11.11 74.2 582 137.9 124.1
12.7 98.7 775 183.7 165.3
15.24 140 1102 260.7 234.6
Grade 1725(250) 7.94 37.4 294 65 58.1 3.5 2.5
9.53 51.6 4.5 89 80.1
11.1 69.7 54.8 120.1 108.1
12.7 92.9 730 160.1 144.1
15.24 139.4 1094 240.2 216.2
 
Square Tubes
Square Tubes  
 
External Dimension THICKNESS (MM)
0.6 0.7 0.08 0.9 1 1.1 1.2 1.35 1.4 1.45 1.5 1.8 2 2.5 2.8 3
mm Weight (Kg/Mtr)
12x12 0.226 0.264 0.301 0.339 0.377 0.328 0.358                  
16x16 0.301 0.352 0.402 0.452 0.502 0.432 0.471 0.53 551 0.569 0.589          
20x20 0.377 0.44 0.502 0.565 0.628 0.544 0.593 0.668 0.695 0.717 0.742          
25x25 0.471 0.55 0.628 0.707 0.785 0.682 0.744 0.837 0.871 0.899 0.93 1.116 1.24      
30x30 0.565 0.659 0.754 0.848 0.942 0.864 0.942 1.06 1.103 1.138 1.178 1.413 1.57 1963 2.198 2.355
 
Galvanized Wire
Galvanized Wire
standard Size(mm) Min. Mass of Zinc Coating(g/m2) Max Resistance at 20˚C(Ω/km) Adherence of coating Tensile Stength Mpa Elong %
BS EN 10244-1 0.8 155 273.5 1D 340-500 10%
1.25 180 112.45 1D 340-500 10%
1.6 195 68.64 1D 340-500 10%
BS EN 10244-2 2 215 34.93 1D 340-500 10%
2.5 245 28.11 1D 340-500 10%
BS EN 10257-1 3.15 255 17.71 1D 340-500 10%
 
Steel Sheets & Plates
Steel Sheets and plates Thickness 0.35mm to 30.0mm
Width 0.5 M to 2.5 M
Length 0.5 M to 18 M
 
Round Tubes
Round Tubes  
 
Outside Diameter THICKNESS (MM)
0.6 0.7 0.08 0.9 1 1.1 1.2 1.35 1.4 1.45 1.5 1.8 2 2.5 2.8 3
D/mm Weight (Kg/Mtr)
Ø12 0.175 0.203 0.232 0.26 0.288 0.316 0.344                  
Ø16 0.234 0.272 0.311 0.349 0.387 0.425 0.462 0.518 0.537 0.556 0.574          
Ø20 0.293 0.341 0.39 0.438 0.485 0.533 0.581 0.652 0.675 0.699 0.722          
Ø25 0.372 0.434 0.496 0.558 0.62 0.682 0.744 0.837 0.871 0.899 0.93 1.116 1.24      
Ø32 0.471 0.55 0.628 0.707 0.785 0.864 0.942 1.06 1.103 1.138 1.178 1.413 1.57 1.963 2.198 2.355
Ø38.7 0.57 0.665 0.76 0.855 0.95 1.045 1.14 1.282 1.334 1.377 1.425 1.71 1.9 2.375 2.66 2.85
Ø42.25     0.835 0.94 1.044 1.148 1.253 1.409 1.466 1.514 1.566 1.879 2.088 2.61 2.923 3.132
 
Steel Angels
Steel Angles
Section Dimensions (mm) Mass kg/M
  a t r (root)  
A40 X 40 X 4 40 4 6 2.42
A40 X 40 X 5 40 5 6 2.97
A40 X 40 X 6 40 6 6 3.52
A45 X 45 X 4 45 4 6 2.74
A45 X 45 X 5 45 5 6 3.38
A45 X 45 X 6 45 6 6 4
 
Tie Wire
Steel Pipe Tubes Galvanized Tie Wire 1.6 MM
1.25 MM
0.8 MM
PVC 0.5 M to 2.5 M
 
 

ASTM A82 / A82M

This specification covers as cold-drawn or galvanized steel wires to be used as such, or in fabricated form, for the reinforcement of concrete. The steel shall be made by one of the following processes: open-hearth, electric furnace, or basic-oxygen. The wires shall be cold drawn from rods that have been hot rolled from billets. The tests described include tension, bending, and reduction of area tests. After undergoing tension test, the tensile and yield strength properties of the test specimen shall conform to the requirements of a reference material based on nominal area of the wire. The specimen for bend test shall withstand being bent at room temperature without cracking on the outside of the bent portion. The reduction of area shall be determined as described in a reference document.